STUDI PENYEBAB KERUSAKAN TEE HEADER PADA INLET FRESH WATER COOLER (Studi Kasus PLTGU Unit 2 di PT. PJB Unit Pembangkit Gresik)

Dimas Haryo, Mahardiko (2015) STUDI PENYEBAB KERUSAKAN TEE HEADER PADA INLET FRESH WATER COOLER (Studi Kasus PLTGU Unit 2 di PT. PJB Unit Pembangkit Gresik). Diploma thesis, POLITEKNIK PERKAPALAN NEGERI SURABAYA.

Full text not available from this repository.

Abstract

ABSTRAK Pada Tugas Akhir ini dipelajari dan dianalisa kebocoran tee header pada inlet fresh water cooler di PLTGU unit dua PT. PJB UP Gresik. Sambungan pipa tee header merupakan salah satu komponen penting dalam sistem perpipaan. Pipa tee header adalah bagian dari sistem perpipaan air laut yang digunakan untuk mendinginkan air tawar di fresh water cooler PLTGU. Standart material yang digunakan untuk perbandingan tegangan menggunakan standart ASTM A 283M. Parameter yang menjadi tujuan analisa adalah tekanan, kecepatan, dan tegangan. Untuk mengetahui nilai tekanan sebelum masuk ke dalam sambungan tee header, terlebih dahulu menghitung besar losses sistem perpipaan dari discharge pompa menuju ke tee header. Besar nilai kecepatan, tekanan, dan tegangan yang ditimbulkan pada tee header dapat di lihat pada simulasi ansys workbench. Nilai tegangan maksimal yang terjadi pada simulasi ansys workbench dibandingkan dengan standart material pipa. Hasil simulasi diperoleh distribusi tekanan terbesar pada tee header dengan variasi tekanan 187837,6 pascal terletak pada bagian sisi pipa yang ditutup sebesar 2,050 x 10 5 pascal. Nilai distribusi kecepatan terbesar pada tee header dengan variasi tekanan 187837,6 pascal, terletak pada sudut pipa didekat sisi outlet sebesar 5,712 m/s. tegangan maksimum untuk simulasi pertama adalah 2,4778 x 10 7 pascal dan simulasi kedua sebesar 1,9994 x 10 7 pascal, sedangkan nilai tegangan minimum material yang diizinkan sebesar 415 Mpa atau 415 x 10 6 Pascal. Kebocoran yang terjadi pada pipa tidak dipengaruhi oleh aliran fluida. Kata Kunci : kebocoran tee header, jalur instalasi sistem, simulasi ansys, tegangan maksimal, standart ASTM A 283M. ABSTRACT In this final project analyzed leaks at the inlet tee header of fresh water cooler in PLTGU units two PT. PJB UP Gresik. Tee header pipe joints is one of the important components in the piping system. Tee header pipe is part of a piping seawater system used to cooling fresh water in the fresh water cooler PLTGU. Standard materials for the stress comparison using standard ASTM A 283M. Parameter which is the goal of analysis is the pressure, speed, and stress. To determine the value of the pressure before going inside tee header, first calculate the losses of piping systems from the discharge pump toward tee header. Great value speed, pressure, and stress at the tee header can be seen in the simulation ANSYS workbench. The value of the maximum stress happened to the simulation ANSYS workbench compare with standard pipe material. The simulation results obtained maximum pressure distribution on the tee header with pressure variation 187,837.6 pascal is located on the side of the pipe closed at 2,050 x 10 5 pascal. The value of the velocity distribution in the header tee with pressure variations 187,837.6 pascal, located in the side of outlet pipe amounted to 5.712 m/s. The maximum stress for the first simulation is 2.4778 x 10 7 pascal and second simulation is 1.9994 x 10 7 pascal, while the value of the minimum stress allowable material of 415 MPa or 415 x 10 6 Pascal. Leakage in the pipe is not affected by fluid flow. Keywords : leakage tee header, lines system installation, ANSYS simulation, maximum stress, standard ASTM A 283M.

Item Type: Thesis (Diploma)
Subjects: T Technology > T Technology (General)
Divisions: Jurusan Teknik Permesinan Kapal > D3 Teknik Permesinan Kapal
Depositing User: Unnamed user with email repository@ppns.ac.id
Date Deposited: 29 Aug 2018 04:05
Last Modified: 29 Aug 2018 04:05
URI: http://repository.ppns.ac.id/id/eprint/219

Actions (login required)

View Item View Item